Town and Country II Slipform Paver

Specifications
General
Maximum paving width: 37.5'.
Maximum paving depth: 20".
Overall machine width: 58" wider than paving width.

Machine length With 12' tracks, 12'.
With 14' tracks, 14'.
With 16' tracks, 16'.
Machine height during paving: 10' 6"
plus depth of concrete.
Machine height during transport: 10' 6" excluding trailer height.
Weight: 12' - 70,000 lbs.,
27' - 78,000 lbs.
15,000-lb. weight package available.


Hydraulic oil: 150 gals.
Fuel: 175 gals.
Water: 220 gals. up to 2000 psi.
Engine oil: 7.3 gals.

Engine
3306 water-cooled Caterpillar diesel standard, 325 HP with 12 volt, 115 amp alternator

Traction
Track pad width: 15".
Track length: 12', 14', 16'.

 Speed Speed up to 45 fpm. (Optional 2-speed motors available).
Ground pressure - with 14' track system - 13.5 psi.
Track height: 30".
Track drive: Sundstrand hydraulic motor coupled to 136:1 planetary gear reducer.

Auger Strike-Off system
Pump: Sundstrand 90 Series, EDC Control.
Diameter: 20".
Type: split in the middle, speed controlled, with individual drive to each side.
Char-Lynn 10000 Series motor, 40.6 cu. in., 3:1 reduction.
Torque: 45,630 in/lbs. per side.
Hydraulic depth adjustment (follows auto-grade if desired).
Telescopic: 12', 25', 24', 38'.
Strike-off follows auger height.

Vibration system
Pump: Sundstrand 90 Series, EDC Control.
Vibration speeds up to 12,000 vpm.
Individual pressure compensation controls.
Hydraulic height adjustment (depth gauge).
Vibrators: 24 Minnich or Wyco, 2 1/2" dia. L-shaped (standard).

 Grade SystemPump: Vickers 20 gpm, pressure compensated.
Cylinders: 5" dia. by 26" stroke.
Posts: 12" dia. by 36" high.
Autograde: Sundstrand or hydraulic sensors on all four corners.

SideformsHeight: 30".
Side movement: 3.5".
Upward movement: 4".
Automatic grade adjustment.

Main Frame
Depth of telescopic tube: 21".
Telescopic range: 12' to 25' wide.
Screw and jack adjustment to ensure constant alignment.

Tamper System
Pump: Sundstrand 42 Series MDC, speed controlled.
Rocker type: staggered to even the shock (eccentric optional).
Tamper crowns with finish pan.

Paving Package
Crowning: Hydraulic (multiple crown capability, optional).
Main section: 12'.
Extensions: 4' each side; 2' each side; 1' each side; 6" each side.
Hydraulic edge over-build.

Options
Standard options available
Town and Country I Slipform Paver

Specifications

Clearance Dimensions   Width:

Pavement width plus 5' 0" at tracks.
Length: 18' 6" plus 3' 8" removable nose plate.

Paving Dimensions Depth: 0 to 20" maximum - total pavement and/or curb height at curb back when 8' sideform extension is used.
Width: 12' to 25', 34' with options.

Weight Approximately 60,000 lbs.

Capacities   Hydraulic oil: 120 gals.
Fuel: 120 gals.
Water wash down system (optional)250 gals.

Traction   Hydraulic motor through planetary gear reducer, Sundstrand hydrostatic pumps with Char-Lynn high torque motors

Speed   0 to 45 fpm.

Engine   Caterpillar 3306 turbo-charged diesel, water-cooled, 325 HP.

Electrical System   12 volt DC
Main Frame   Heavy duty box section supporting power unit, hydraulic pumps, reservoir, controls and ladders.

Frame Extensions   Fabricated steel beams power widened by synchronized jackscrews through hydraulic motor driven shaft each side.

Machine Lift Cylinders
Four pedestal cylinder lift the machine off grade for width change, loading or unloading and ease of clean up and servicing. Will clear 50" for load out with tracks on or off.

Paving Extrusion Meter
Heavy-duty construction, basic 12' with bolt-on extensions to 25' standard width. Extensions furnished: two 1', two 2', two 3', two 4' mm and two 2 1/2'. Able to balance crown or offset when required.


Meter crown controlled by electric over hydraulic jackscrew for "no-drift" setting. Crown gauge easily read from ground level at left side of machine. Maximum crown 0 to 4" at 25' (1/4' per ft.). Inverted crown maximum 1/8" per ft. Edge wings control surface at pavement outer edge, hydraulically actuated by valve at back of track.

Tamper Bars   Telescopic bar construction. Variable hydraulic drive. Elliptical "tucking" motion provides even flow of concrete to extrusion meter.

Vibration
Internal type, hydraulic motor in head; 12 vibrators standard, 24 outlets provided. Individual variable speed controls. Additional vibrators optional.

Sideforms
Hydraulically raise and lower to grade a total of 4", spring-loaded to seal to grade, hydraulically retract 1 3/4" each side to clear header and/or previously placed pavement. Paving depth 0 to 20" with optional 8" extension available.

Augers and Strike-Off
Telescopic auger shaft with bolt on flights in 1" increments, 20" diameter heat treated. Auger and strike-off telescope as machine frame widens or narrows.

Steering   Automatic reference line set 2' 6" to 8' 0" from edge of slab.
Controls
12 volt DC and mechanical. Automatic surface profile control with cross slope.

Off-String Alarm System
Automatic off-string alarm when sensor wand leaves string or moves too far from normal position. Resets automatically.

Sensors
Electro-magnetic. No Contacts. Temperature stable, not affected by moisture.

Crawler Tracks
Length: Track beam 18' 6" end-to-end. Track pad width 12".

Machine Access   Rear access to machine on either side by track step, to telescopic platform, which covers the full range of paving width - 12' to 25'.

Options 

> Grade line group: 1000' line, stakes, brackets hangers and winch.

> Curb mules for extruding monolithic curb and gutter.

 

> Curb mule cut-off.

Metal keyway punch and former with manual bent tie bar inserter


> Centerline tape inserter.

 

> Center tie bar inserter.

 

> High-pressure washdown system.


> Kit to extend machine to 34' paving width.

 

> Extra hydraulic internal vibrators.


> 10' shoulder paving kit.

 

> Spare parts kit.

 

Contact us for special options
 

Town And Country II Belt Placer

Specifications

Operating Specifications


Working width: pavement width plus 5' 8 1/2".
3' 6" on the belt side.
2' 2 1/2" on side opposite belt. Travel speed: 0-60 fpm.
Working weight: 60,000 lbs. approx.

Capacities
Hydraulic oil: 220 gallons.
Fuel: 45 gallons.
Engine oil: 7.3 gallons.
Coolant: 10 gallons.

Traction
Four 7' long tracks with 12" wide grouser pads.
Two-speed hydraulic motors operating planetary gear reducers.

Engine
Caterpillar 3306B 6 cylinder water cooled engine developing 325 HP
@2100 rpm with 115 amps alternator.

Electrical System
12 volt DC


Auger Spreader Option
20" diameter quick detach auger system with individual speed controlled functions for each side of auger.


The auger can be placed on front or back of machine for left or right hand concrete placement.


The auger spreaderis string-line controlled for elevation. Manual control with power crown capability on the go.

Auxiliary Belt Option
Belt is 25' long and 46" wide.
Belt swings 40 degrees and can be hydraulically lifted 4'.
Planetary driven by 2 torque hubs coupled to Sunstrand motors.
18" diameter slide lagged head roller.
12" diameter tail pulley.

Folding Belt  

Belt width - 54"
Planetary driven by 2 torque hubs.
Adjustable folding speed (down to 4 seconds).
Belt speed up to 700 fpm.
2 40" long by 4" diameter fold cylinders.
Special snubber roller feature for handling very low slump concrete.
Belt folding point hydraulically adjustable for height for different haul roads.

Load Legs
Self contained hydraulic load legs for lifting machine 4' high.

Elevation Legs
48" vertical stroke.

Standard Paving Widths
0 to 25' extensions available on request.
Depths to 20".

Power Widening
12' to 20' - 60" sections are added past 20'.

Town And Country I Belt Placer

Specifications

Operating Specifications
Working width: Pavement width plus
5' 8 1/4" x 3' 6" on belt side, 2' 2 1/4" on site opposite belt.
Travel speed: 0 to 52 fpm.
Working weight: 59,000 lbs.
Capacities
Hydraulic oil: 106 gals.
Fuel: 82 gals.
Lubricant oil: 5 gals.
Coolant: 10 gals.

Traction
Hydraulic motor through planetary gear reducer. Sundstrand pump, Char-Lynn motor, torque hub design.

Engine
Caterpillar 3306B 6 cylinder, water cooled, turbo-charged diesel, 250 HP.

Electrical system
12 volt DC

Steering
Automatic from reference line set 2' 6" to 8' from edge of slab.


Placement Belt
60" wide. Hydraulic motor drive through planetary gear reducers. Variable operating speed 0 to 500 fpm. Hydraulic cylinders raise belt vertically to allow haul units to pass and lower to receive material.

Augers & Strike-Off
Strike-off depth: minus 10" to plus 20" with standard side forms.
Strike-off width: 12' 0" to 25' 0".


Auger strike-off: Telescopic auger shaft and strike-off assembly with clamp-on auger flight extensions. Hydraulically driven 20" diameter auger with variable speed, 0 to 75 RPM, in either direction. Dual augers with hydraulically crownable strike-off at widths above 22'.

Machine Access
Front access top machine by ladder.

Controls
12 volt DC and mechanical.


Crawler Tracks
Track beam length: 20' 7" end-to-end, 21' 1" overall.
Track pad width: 12".

Machine Lift Cylinders
Four pedestal cylinders lift the machine off grade for width change, loading or unloading and ease of clean up and service. Will clear 50" for load out with tracks on or off.

Options
- Caterpillar 3304B 4 cylinder engine, 165 HP with 48" wide belt conveyor.
- Power frame-widening kit.
- Corner lift cylinders in addition to standard pedestal cylinders.
- High-pressure wash down kit, 184 gals. capacity.
- Grade line group: 1000' of line, stakes, brackets and hangers.
- Custom width kit.
- Adjustable belt fold height kit.
- Contact us for special options.
 

Town and Country 2600 Texture Cure Machine

Specifications

Power Unit  

4B3T Cummins water cooled diesel engine, 76hp at 2200 rpm.
12 volt system with 63 amp alternator.
Other engines available upon request.

Capacities
Diesel fuel: 35 gals.
Hydralic oil: 34 gals.
Cure tank: 130 gals standard, 300 gals optional.
Optional water tank: 100 gals.

Dimensions
Minimum height - 9ft. 5in.
Maximum height - 11ft. 5in.
Overall width (Minimum) - 16ft. 10in.
(Maximum) - 32ft. 10in.
Load Width (no disassembly) - 10ft. Fold up ladders at each end for access to platform, console and cure tank.

 Weight   14,000lbs. at 26' curing width, without options.

Tracks
12" wide grouser pads w/low profile cleats.
10' long Berco crawler system.
160 fpm forward and reverse.
35:1 fairfield drive torque hubs w/brakes.

Hydraulics
Track System: closed loop Sunstrand pump.
Functions System: Vickers pressure compensated pump.
10-micron absolute filter system (spin on type).
Char-Lynn Motors

Electronics   Sundstrand 12 volt sensors. 12 volt, 900 cca battery.

Cure System Roper 17 gpm gear pump. Cure tank can siphon from barrels or totes on either side of machine. The fold up spray bar is height adjustable and skirted, and side nozzles can be turned on or off to cure slab edge.
Flushable canister-type spray filter.

Optional Equipment  

300 gals. cure tank 100 gals.

water tank.

Astro-turf drag.

Visqueen roller. Transport wheels.

Power wash system w/reservoir.